石膏找平顧名思義就是使用石膏板或是石膏粉與膠調和進行墻面或是天花表面不平整范圍的填平工作。這種方法可以進行局部找平且不需要將地面抬高，施工起來比較方便，價格相對來說較為便宜。濟南石膏粉找平墻面步驟：

Gypsum leveling, as the name suggests, is the use of gypsum board or gypsum powder mixed with glue to fill in the uneven areas of the wall or ceiling surface. This method can perform local leveling without raising the ground, making construction more convenient and relatively inexpensive. Jinan gypsum powder leveling wall steps:

1

one

先對墻面進行清理。如果墻面有裂縫、孔洞等情況的話，可以先嵌入石膏粉將它們填補平整。

Clean the wall first. If there are cracks, holes, etc. on the wall, you can first embed gypsum powder to fill them flat.

2

two

涂刷界面劑，防止基層開裂。使用滾筒均勻涂刷，陰陽角區域用涂刷滿漿，涂刷之后注意保持清潔。

Apply interface agent to prevent cracking of the base layer. Use a roller to evenly brush, and fill the internal and external corners with paint. After brushing, pay attention to maintaining cleanliness.

3

three

防開裂處理。已經開裂的區域先做修補，使用抹刀開八字縫，用石膏刷清掃粉塵，直接鋪貼牛皮紙，涂刷石膏，再使用網格布鋪滿墻面，使兩塊布之間搭接嚴密，重新疊加部分不低于50mm。

Anti cracking treatment. The area that has already cracked should be repaired first. Use a trowel to open a zigzag joint, use a gypsum brush to clean the dust, directly apply kraft paper, apply gypsum, and then use a grid cloth to cover the wall surface, so that the overlap between the two pieces of cloth is tight, and the re overlapping part should not be less than 50mm.

4

four

接縫處理。不同材質交接處粘貼接縫時，需要粘貼平整牢固。

Joint treatment. When pasting joints at the junction of different materials, it is necessary to stick them flat and firmly.

5

five

陰陽角彈線。用水平儀在墻面上彈出水平線、垂直線。和頂棚水平線。用石膏粉將邊角區域不平整的地方刮平，之后確定墻面大面積平整度的控制線。

Snap the lines at the internal and external corners. Use a spirit level to mark horizontal and vertical lines on the wall. And the horizontal line of the ceiling. Use gypsum powder to scrape off uneven areas at the edges and corners, and then determine the control line for the large area flatness of the wall.

6

six

粉刷基層。根據已經標記好的控制線，批刮石膏。將石膏粉與清水按照比例調兌、攪拌均勻，并在規定的時間內使用完。如果批刮的厚度不超過10mm，則需要鋪貼一層網格布，之后再批刮一層石膏。

Painting the base layer. According to the marked control line, apply plaster in batches. Mix gypsum powder and clean water in proportion, stir evenly, and use it within the specified time. If the thickness of the batch scraping does not exceed 10mm, a layer of grid cloth needs to be laid and then a layer of gypsum needs to be scraped.

7

seven

面層施工?；鶎拥氖鄬痈稍镏?，需要在面層涂刷一層石膏，批刮滿漿，并找平粗糙的表面，使面層光滑平整。接縫處理。不同材質交接處粘貼接縫時，需要粘貼平整牢固。

Surface layer construction. After the gypsum layer of the base layer is dry, it is necessary to apply a layer of gypsum on the surface layer, scrape the paste thoroughly, and level the rough surface to make the surface layer smooth and flat. Joint treatment. When pasting joints at the junction of different materials, it is necessary to stick them flat and firmly.

此外石膏找平和刮膩子的施工方式是有一些差異，材料也不同。正常情況下石膏適用于內部墻面施工，膩子具有室內外施工的不同點，可以根據自己的需求來施工。石膏更多的是做局部找平處理，膩子更適合做大面積批刮施工。更多相關內容就來我們網站http://www.wxccxs.com咨詢！

In addition, there are some differences in the construction methods and materials of gypsum leveling and putty application. Under normal circumstances, gypsum is suitable for internal wall construction, while putty has different characteristics for indoor and outdoor construction, and can be constructed according to one's own needs. Gypsum is mainly used for local leveling, while putty is more suitable for large-scale batch scraping construction. For more related content, come to our website http://www.wxccxs.com consulting service